View AMS001_8289049.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

ams00x ? embedded bluetooth low energy solution s ads - ms00x - 107r ? preliminary data sheet september 14, 2015 ?201 4 - 2015 ackme networks. http://ack.me AMS001 / ams002 data s heet
ams00x ? embedded bluetooth low en ergy solution ads - ms00x - 107r ? preliminary data sheet page | i ?201 4 - 2015 ackme networks. http://ack.me september 14, 2015 disclaimer while the information provided in this document is be- lieved to be accurate, it is under development and ackme networks reserves the right to make changes without further notice to the product de scribed herein to improve reliability, function, or design, and makes no guarantee or warranty concerning the accuracy of said information, nor shall it be responsible for any loss or damage of whatever nature resulting from the use of, or reliance upon, s uch information. ackme networks makes no warranties of any kind, whether express, im- plied or arising by custom or course of trade or perfor- mance, and specifically disclaims the i mplied warranties of title, non - infringement, merchantability, or fitness for a particular purpose. no part of this document may be copied, reproduced, stored in a retrieval system, or transmitted, in any form or by any means, electronic, mechanical, photographic, or otherwise, or used as the basis for manufacture or sale of any ite ms without the prior written consent of ackme networks. trademarks ackme networks and the ackme networks logo are trademarks of ackme networks. wiced? is a trade- mar k of broadcom ? corporation, inc. bluetooth? is a trademark of the bluetooth sig. other trade marks in this document belong to their respective owners . copyright ? 201 4 - 2015 ackme networks. all rights reserved. document number: ads - ms00x - 107r release date: september 14, 2015 contact http://ack.me/contact about this data s heet this document provide s information on the family of ams00x bl uetooth low energy (bluetooth smart) mod- ules from ackme networks. organization this data sheet is organized into the following sections : ? features & applications ? general description, section 1 ? block diagram, section 2 ? electrical specifications, section 3 ? bluetooth rf specifications, section 4 ? pinout and signal descriptions, section 5 ? design guidelines, section 6 ? regulatory certification, section 7 ? packaging, handling & storage, rohs, section 8 ? ordering information, section 9 ? revision history & glossary , section 1 1
ads - ms00x - 107r ? preliminary data sheet page | ii ?201 4 - 2015 ackme networks. http://ack.me september 14, 2015 ams00x family data sheet embedded bluetooth low energy solution features ? bluetooth low energy (bluetooth smart) module s fully certified to meet bluetooth version 4.1. ? integrated 8 mbit spi - serial flash supports firm- ware up da tes and multiple on - board applications ? on - board pcb - style antenna ? arm? cortex? m3 - based microprocessor core ? adaptive frequency hopping (afh) ? p rogrammable rf transmit power control ? operation directly from a battery or mains supply ? small size enables integration into most sensor products and applications ? secure over - the - air (ota) software update using industry - standard aes - 128 security ? easily integrated into existing or new product s us- ing truconnect, ackmes configurable bluetooth low energy application (pre - installed on every module) ? mul tiple services including ackme truconnect , beacon , ibeacon, plus more interfaces * ? a/d converter : 7 channel s with 4 modes providing variable resolution (10 - 13 enobs ), sampling rate (5.9 - 187 khz) and conversion latency (5 - 1 71 s) ? u s art: 1 x 4 - wire up to 1.5 m bit/s for general use, 1 x 2 - wire for in - circuit programming ? spi: 1 x master , 1 x slave at 12 mbit /s ? i 2 c: 1 x i 2 c master interface up to 1 mhz ? gpio: up to 12 gpios (overlaid with peripherals), programmable pull - up/pull - down resistors with 16 ma drive strength at 3.3v (2 ma standard) . ? 4 x pwm channels each with a 10 - bit counter clocked at 128 k hz. ? wake - up : wake from gpio for ultra - low power operation . * some interfaces share module pins operational & radio ? operational voltage : 1. 8 v - 3.6v ? operational temperature range: - 3 0 c to + 85 c ? size : 17.6 x 11.4 x 2 . 4 mm (0. 70 x 0. 45 x 0. 10 ) ? weigh t : 0.0 4 oz ( 1. 2g) ? current consumption @ 3. 0 v, 25c - deep sleep : 1 .65 a (typ.) - sleep : 12 a - AMS001 ? active receive : 12 .8 ma ? active transmit : 10 . 8 ma - ams002 ? active r eceive : 26 . 6 ma ? active transmit : 22. 0 ma ? rf t ransmit p ower : +4 dbm (max.) ? r eceive s ensi tivity : - 94 dbm applications ? health & fitness - fitness equipment - heart rate monitors - weight scales - thermometers - pedometers - glucose meters - blood pressure monitoring ? retail - advertising and beaconing - proximity detection - point - of - sale ? home & industrial control and automation - appliance control and monitoring - doors/window monitoring - alarms - wireless cable replacement - environmental & energy monitoring - wireless sensing, remote data logging ? consumer - toys - robots remote controls
ams00x ? embedded bluetooth low energy solution ads - ms00x - 107r ? preliminary data sheet page | iii ?201 4 - 2015 ackme networks. http://ack.me september 14, 2015 contents 1 general description ................................ ............... 1 2 block diagram ................................ ........................ 2 3 electrical specifications ................................ .......... 3 3.1 absolute maximum ratings ............................ 3 3.2 recommended operating conditions ............ 3 dc opera ting conditions ........................ 3 environmental conditions ...................... 4 3.3 power consumption ................................ ....... 4 3.4 input/output pins ................................ ........... 5 3.5 adc specifications ................................ .......... 5 4 bluetooth rf specifications ................................ ... 6 4.1 summary rf specifications ............................. 6 4.2 receiver specifications ................................ ... 6 4.3 transmitter specifications .............................. 7 5 pinout and signal descriptions .............................. 8 5.1 pinout ................................ .............................. 8 5.2 pin description ................................ ................ 8 6 design guidelines ................................ ................. 10 6.1 recommended pcb footprint ...................... 10 6.2 routing recommendations .......................... 10 6.3 soldering information ................................ ... 11 6.4 ams00x photograph ................................ ..... 11 6.5 application examples ................................ .... 12 uart application for configuration and streaming ................................ ............................. 12 6.6 operation using truconnect ........................ 12 bootup configuration ........................... 12 factory reset ................................ ........ 13 command and stream mode ............... 13 gpio configuration & usage ................ 13 7 regulatory certification ................................ ....... 14 7.1 united states ................................ ................ 14 labeling and user informatio n requirements ................................ ....................... 14 rf exposure ................................ .......... 15 external antenna ................................ .. 15 further information .............................. 15 7.2 canada ................................ .......................... 15 labeli ng and user information requirements ................................ ....................... 15 external antenna types ........................ 16 further information .............................. 16 7.3 europe ................................ .......................... 17 labeling and user information requirements ................................ ....................... 17 external antenna requirements .......... 17 further information .............................. 17 7.4 australia ................................ ........................ 18 external antenna requirements .......... 18 further information .............................. 18 7.5 new zealand ................................ ................. 19 external antenna requirements .......... 19 further information .............................. 19 8 packaging, handling & storage, rohs ................. 20 8.1 packaging ................................ ...................... 20 8.2 tape and reel specifications ........................ 20 8.3 handling & storage ................................ ....... 22 8.4 rohs directive ................................ .............. 22 9 ordering information ................................ ........... 23 10 revision history & glossary ................................ . 24 10.1 revision history ................................ ............ 24 10.2 glossary ................................ ........................ 24
ams00x ? embedded bluetooth low energy solution general description , section 1 ads - ms00x - 107r ? preliminary data sheet page | 1 ?201 4 - 2015 ackme networks. http://ack.me september 14, 2015 1 general description the family of ams00x bobcat module s from ackme network s is based on an ultra - low power bluetooth low energy (bluetooth smart) soc from broadcom cor- poration. all module s incorporate serial - flash memory and a printed antenna to provide a state - of - the - art ful- ly - certified bluetooth 4.1 solution. an integrated so lution avoids difficult rf layout and enables designers to rapidly embed bluetooth low en- ergy into virtually any device. the AMS001 (low power) version slashes active power consumption for applications requiring multi - year bat- tery life, while the ams002 (l ow cost) version provides the lowest cost solution suitable for price sensitive ap- plications. the modules are 100% footprint compatible. modules ship with ackme tru con nect, an easy - to - use application enabling control and configuration via uart - serial and r emote terminal interfaces . trucon- nect virtually eliminates difficult and time - consuming software development effort and vastly reduce s prod- uct development cycles. with dimensions of just 17 . 6 x 1 1 . 4 mm , a wide tem- perature range, and a n ultra - low power vers ion , the module is suitable for integration into any battery - powered embedded wireless application. the bluetooth low energy soc from broadcom is pur- pose - designed to support the entire spectrum of blue- tooth smart use cases for medical, home automation, acc essory, sensor, retail and wearable market seg- ments. superior receive sensitivity, a n integrated rf transmit power amplifi er and transmit/receive switch , along with the on - board antenna, provide extended range and full compatibility with all bluetooth 4.1 de- vices . at the heart of all ams00x modules is a bluetooth low energy soc with a high - performance arm? 32 - bit cor- tex? - m 3 core operating at a frequency of 24 mhz . the soc includes is configured to boot applications stored in the 8 mbit serial flash memory a vailable on - board the module. the broadcom ble soc supports adaptive frequency hopping. each module provides an extensive array of i/o and peripheral interfaces. t he following interfaces are available , many of which are accessible with i/o multi- plexing and alternate function capabilities : 7 x a/d convert er channels ? 2 x uart interfaces: 1 x 4 - wire, 1 x 2 - wire ? 1 x spi master , 1 x spi slave bus ? 1 x i 2 c interface ? up to 1 2 x ultra - low power wake input ? 32khz crystal interface the module may be powered directly from a battery supply in the range 1. 8 - 3.6v includ ing 2xaaa, 2xaa, or a single lithium coin cell. internal power domains are a utomatically adjusted to minimiz e power dissipation based on user activity. var- ious power modes, including an ultra - low power deep sleep mode, are provided to minimize total avera ge power consumption and maximize battery life. c ustom factory settings may be saved to a non - erasable area of static memory to enable out - of - the - box custom product configuration and the ability to return product s incorporating the module to a known factor y reset state. the module may be woken from deep sleep mode by a level transition on the gpio assigned for stream mode selection . other gpios may be dynamically allocated for control and status including a ble connection indicator, serial bus mode control and status indicator , audible alerts and factory reset . a n internal 32khz low - power oscillator is available by default for non - critical timing requirements . applica- tions requiring an accurate real - time clock may connect an (optional) external 32khz crystal . all versions of the module have bluetooth bqb sig cer- tification, and fcc & ic modular approval for use in the united states and canada , and ce approval for use in europe and other countries.
ams00x ? embedded bluetooth low energy solution b lock diagram , section 2 ads - ms00x - 107r ? preliminary data sheet page | 2 ?201 4 - 2015 ackme networks. http://ack.me september 14, 2015 2 b lock diagram figure 1 is a block diagram showing the architecture of ams00x bluetooth low energy module s . the major components are a bluetooth low energy soc from broadcom , 24mhz crystal, 8 mbit serial flash and a pcb - style antenna . the AMS001 version also includes a high - efficien cy dc - dc switching regulator to significantly re- duce active mode power consumption. t he bluetooth soc is powered by a n arm cortex m3 - based processo r run ning at 24 mhz . the soc is driven by a 24 mhz crystal, an on - board real - time clock may be (optionally) enabled by connecting an external 32khz crystal. the 8 mbit serial flash memory stores the ackme truconnect? application and user configuration , an d enable s secure over - the - air (ota) wireless firmware updates. the on - board pcb antenna simplifies rf inte- gration into end products. an extensive array of analog and digital peripherals in- cluding adcs , gpios , pwms and multiple serial inter- faces such as uar t , spi and i2c are accessible via mod- ule pins. th e module is powered by a single - rail battery or mains supply . figure 1 . ams00x architecture vdd 32khz xtal spi uart i2c adc gpio pwm reset 8 mbit serial flash ams00x antenna dc - dc AMS001 only 24mhz bluetooth low energy soc arm cortex m3
ams00x ? embedded bluetooth low energy solution electrical specifications , section 3 ads - ms00x - 107r ? preliminary data sheet page | 3 ?201 4 - 2015 ackme networks. http://ack.me september 14, 2015 3 electrical specifications 3.1 absolute ma ximum rating s caution ! the absolute maximum ratings in table 1 and table 2 indicate levels where permanent damage to the de- vice can occur, even if these limits are exceeded for only a brief duration. func tional operation is not guaranteed un- der these condi tions. operation at absolute maximum conditions fo r extended periods can adversel y affect long - term reliability of the device. table 1 . absolute maximum voltage ratings symbol rat ings min . max . unit v dd max dc supply voltage applied to vdd pin gnd - 0.3 3.8 v v io voltage on input or output pin gnd - 0.3 vdd max + 0.3 v table 2 . absolute maximum environmental ratings characteristic note min . max . unit stor age temperature C - 40 + 125 c relative humidity non - condensing (storage) C 6 5 % 3.2 recommended operating conditions functional operation is not guaranteed outside the limits shown in table 3 and table 4 , and operation outside these limits for extended periods can adversely affect long - term reliability of the device. dc operating conditions table 3 . recommended dc operating conditions symbol ratings 1 min . typ ical max . unit vdd dc supply voltage applied to vdd pin on - board serial flash read - only 1.8 C 3.63 v on - board serial flash read and write 2.1 C 3.63 v on - board serial flash at power - on 2.25 2 C 3.63 v note s : 1. overall performance degrades beyond minimum and maximum sup ply voltages. 2. the module may fail to boot if this condition is not met when power is initially applied.
ams00x ? embedded bluetooth low energy solution electrical specifications , section 3 ads - ms00x - 107r ? preliminary data sheet page | 4 ?201 4 - 2015 ackme networks. http://ack.me september 14, 2015 environmental conditions table 4 . recommended environmental conditions characteristic note min . max . unit ambient temperature - 30 +85 c relative humidity non - condensing (operating) C 85 % 3.3 power consumption the ams00 x automatically adjusts power dissipation based on user activity to minimize power usage . the p ower consumption in each state, and for each version of the module , is specified in table 5 . table 5 . power c onsumption ( 3.0v, 25c) operational state note typical unit deep sleep 1 ble chip (0.65 a) + serial flash (1 a) 1.65 a sleep wake in <5 ms 12.0 a AMS001 active receive receiver enabled and operating at 100% duty cycle 12.8 ma active transmit 2 transmitter enabled and operating at 100% duty cycle 10.8 ma ams002 active receive receiver enabled and operating at 100% duty cycle 26.6 ma active transmit 2 transmitter enabled and operating at 100% duty cycle 22.0 ma notes : 1. requires 10k pullup resistor on module pin 6. see 6.5.1 , u art application for configuration and streaming 2. rf transmit power = 0db m
ams00x ? embedded bluetooth low energy solution electrical specifications , section 3 ads - ms00x - 107r ? preliminary data sheet page | 5 ?201 4 - 2015 ackme networks. http://ack.me september 14, 2015 3.4 input/output pin s all digital i / o pins have a maximum input voltage rating of v ss - 0.3v to v dd +0.3v. the maximum supply voltage is 3.63v. consequently, digital i/o pins are not +5v tolerant. table 6 . digital i/o pin levels symbo l description min. typical max. unit v i l input low voltage C C 0.4 v v i h input high voltage 0.75 x vdd C C v v ol output low voltage 1 C C 0.4 v v oh output high voltage 1 vdd C 0.4 C C v notes : 1. at the specified drive current for the pin. 3.5 adc specifica tions table 7 . adc specifications ( @ 25 c) parameter symbol conditions min. typ. max. unit input channels C C 8 C C channel switching rate f ch C 133.33 C kch/s input signal range v inp 0 C 3.63 v reference settling time C 7. 5 C C s input resistance r in effective, single ended C 500 C k input capacitance c in C C 5 pf conversion rate r c 5.859 C 187 khz conversion time tc 5.35 C 170.7 s effective number of bits enob 10 C 13 bits abs. voltage meas. error C C 2 C % current i C C 1 ma leakage current i leak age C C 100 na pow er - up time t pup C C 200 s integral nonlinearity i nl lsbs at the 10 - bit level - 1 C 1 lsb differential nonlinearity d nl lsbs at the 10 - bit level - 1 C 1 lsb
ams00x ? embedded bluetooth low energy solution bluetooth rf specifications , section 4 ads - ms00x - 107r ? preliminary data sheet page | 6 ?201 4 - 2015 ackme networks. http://ack.me september 14, 2015 4 bluetooth rf specifications unless otherwise stated, the specifications in this section apply wh en the operating conditions are within the limits specified in section 3.2 , recommended operating conditions . functional operation outside these limits is not guar- anteed. all specification s are measure d with a coax pigtail soldered to the pcb antenna feed point , with vdd = 3.0v and at a room temperature of 25c . 4.1 summary rf specifications table 8 . summary rf specifications feature supported description bluetooth standard versio n 4.1 frequency band 2.40 0 ghz C 2. 50 0 ghz channels (2mhz spacing ) 3 x advertising channels @ 2402 / 2426 / 2480 mhz 3 6 x data channels maximum raw data rate 1 mbit/s maximum application data rate 0.27 mbit/s modulation type dsss: gfsk ( modulation in dex = 0.5) maximum rf input - 10 dbm typical receive sensitivity - 94 dbm maximum rf tx output power + 4 dbm carrier frequency accuracy 20 ppm (2 4 mhz crystal , 2 0 ppm stability @ 25 c) 4.2 receiver specifications table 9 . receiver performance specifications parameter condition/notes min . typ ical max . unit frequency range C 240 2 C 2 480 mhz operating temperature C - 30 C + 85 c receive sensitivity 200 x 37 - byte packets with 30.8% per C - 94 C dbm max imum receive level - 10 C C dbm
ams00x ? embedded bluetooth low energy solution bluetooth rf specifications , section 4 ads - ms00x - 107r ? preliminary data sheet page | 7 ?201 4 - 2015 ackme networks. http://ack.me september 14, 2015 4.3 transmitter specifications table 10 . transmitter performance specifications parameter condition/notes min typ ical max unit frequency range C 240 2 C 2 480 mhz operating temperature C - 30 C + 85 c transmit power 2 C C 4.0 C d bm transmit power variation process dependent C 2.0 C transmit power range adjustable via software control - 20 4 dbm channel spacing C 2 C mhz
ams00x ? embedded bluetoot h low energy solution pin out and signal descriptions , section 5 ads - ms00x - 107r ? preliminary data sheet page | 8 ?201 4 - 2015 ackme networks. http://ack.me september 14, 2015 5 pin out and signal descriptions 5.1 pinout a top view of the ams00x pinout is depicted in figure 2 . all dimensions are in thousands of an inch. a recom- mended pcb footprint is provided in section 6.1 . figure 2 . ams00x pinout (top v iew C pins not visible from top!) 5.2 pin description table 11 . a m s 00 x pin definitions pin name type 1 primary function alternate & other function(s) 1 gnd s ground - 2 prog _rx i prog r x - 3 prog _tx o prog t x - 4 gpio_0 i/o reserved 4 not available as digital i/o . reserved fo r future use as spi_mosi, i2c_sda 5 gpio_1 i/o reserved 4 not available as digital i/o . reserved fo r future use as spi_clk, i2c_scl 6 gpio_2 i/o u ser tx spi_mo si (s lave ) , adc, gpio 7 gpio_3 i/o user _rts spi_miso (s lave ) , adc . , gpio 8 reset_n i system reset - 9 gpio_4 i/o user _cts spi_clk (s lave ), gpio 10 gpio_5 i/o user _rx spi_cs ( s lave ), gpio
ams00x ? embedded bluetoot h low energy solution pin out and signal descriptions , section 5 ads - ms00x - 107r ? preliminary data sheet page | 9 ?201 4 - 2015 ackme networks. http://ack.me september 14, 2015 pin name type 1 primary function alternate & other function(s) 11 gpio_6 i/o gpio spi_mosi (m aster ) , factory_reset 3 12 gpio_7 n/c reserved 4 reserved. not available as digital i/o 13 gpio_8 i/o gpio spi_miso (m aster ) 14 gpio_9 i/o gpio spi_clk (m aster ) 15 gpio_10 2 i/o gpio adc, pwm 16 gpio_11 i/o gpio adc, pwm 17 gpio_12 i/o gpio spi_cs (master), adc 18 gpio_13 2 i/o gpio ad c, pwm, xosc32_out 19 gnd s ground - 20 gpio_14 2 i/o gpio adc, pwm, xosc32k_in 21 vdd s vdd - 22 - 27 gnd s ground - notes : 1. i = input , o = output , s = supply 2. the drive strength of standard gpios is 2ma, the drive strength of this gpio is 16ma. 3. the fac tory_reset pin may be moved to a different gpio, but it may not be de - assigned 4. connected to spi serial flash inside the module
ams00x ? embedded bluetooth low energy solution design guidelines , section 6 ads - ms00x - 107r ? preliminary data sheet page | 10 ?201 4 - 2015 ackme networks. http://ack.me september 14, 2015 6 design guidelines 6.1 recommended pcb footprint all dimensions in figure 3 are in thousands of an inch u nless otherwise marked. figure 3 . a m s 00 x recommended footprint (top) 6.2 routing recommendations when designing a carrier board, the addition of ground fill directly underneath the module, rather than signal or power traces, is stro ngly advised . all ground pads adjacent to antenna pins must be connected to a solid ground plane. do not route any metal or pcb traces underneath the printed pcb - antenna! failure to comply with these recommendations will almost certainly result in degrad ed performance of the radio receiver and/or transmitter . for optimal range, provide a clearance of 5mm (0.2) above, below and to the front and sides of the antenna end of the module. avoid routing traces not connected to ground under the vias in the shaded rectangle. measurements are in thousandths of an inch. 265 265 11 5 11 5
ams00x ? embedded bluetooth low energy solution design guidelines , section 6 ads - ms00x - 107r ? preliminary data sheet page | 11 ?201 4 - 2015 ackme networks. http://ack.me september 14, 2015 6.3 solder ing information figure 4 . recommended solder reflow profile 6.4 ams00x photograph figure 5 . a m s 00 x photograph (top)
ams00x ? embedded bluetooth low energy solution design guidelines , section 6 ads - ms00x - 107r ? preliminary data sheet page | 12 ?201 4 - 2015 ackme networks. http://ack.me september 14, 2015 6.5 application examples u art application for configuration and streaming follow the schematic in figure 6 to connect a host mcu uart to the user uart serial interface of the ams00x mod- ule. this application enables a host mcu to configure the mo dule using command mode, and transfer data back and forth to a remote device via the bluetooth le wireless interface using stream mode . uart hardware flow control is not required, but is recommended for streaming continuous data. figure 6 . connecting a host mcu to the AMS001/ams002 user uart note : the 10k pullup resistor on p in 6 allows the module t o go to sleep and stay asleep. it also enables sleep current to be reduced to a typical value of 1.65 ua . if pin 6 is not driven high t he wake - up circuit may be highly sensitive to small variations in capacitance or voltage on module pins . module sleep current may also remain higher, at around 200ua. 6.6 operation using tru connect the information in this section provides a very brief overvi ew of basic operation using truconnect. for de- tailed information, consult the truconnect reference guide available online at http://truconnect.ack.me bootup configuration at boot up , truconnect attempts to load save d configu- ration settings i.e. the saved state of truconnect varia- bles . there are three configuration sets that may be loaded, depending on the state of the module . user settings may be saved/ changed as required, f actory settings may be saved only once, and default settings are hardcoded into the app at compile time and cannot be changed. configuration load at boot time occurs in the following sequence: 1. user settings . this configuration is set by a user and saved by the truconnect save command without any su pplied argument s . user configuration can be changed at any time , and the configuration is delet- ed when a factory reset is performed. if no user config uration is present or it is corrupted then truconnect attempts to load the factory settings.
ams00x ? embedded bluetooth low energy solution design guidelines , section 6 ads - ms00x - 107r ? preliminary data sheet page | 13 ?201 4 - 2015 ackme networks. http://ack.me september 14, 2015 2. factory set tings . f actory configuration provide s a way to save a configuration at manufacturing time. factory settings are saved using the truconnect command: save factory save with the lock option to ensure that factory settings cannot be overwritten: sav e factory lock caution! the factory configuration cannot be changed after sav ing with the lock option . if no factory configuration is present or it is corrupt- ed , then truconnect loads the basic c ompile - time default configuration . 3. default setting s . the default configuration is a sane set of default s that are hardcoded in trucon- nect . factory reset the module may be factory reset with a truconnect command, or by asserting the factory reset pin at bootup. to factory reset via a command, issue: > fac to factory reset via the factory reset gpio: 1. identify the gpio used for factory reset by issu- ing the command to get gpio usage: get gp u ( t he factory reset default is gpio 6 ). 2. assert a logic 1 (high) on the pin associated with the factory reset gpio 3. assert and de - assert the reset pin to force the module to reboot 4. wait at least 10 seconds (the status of factory reset is printed to the user uart 5. de - assert the factory reset pin command and stream mode t he module boots into serial bus command mode b y default and accepts configuration and control com- mands via the user uart. once the configuration is saved, stream mode may be used to transfer data be- tween the serial interface and a remote device con- nected to the bluetooth le wireless interface. to togg le between command mode and stream mode, the gpio alternate function mode_sel may be used (if config- ured) , or to simply transition from command mode to stream mode, use the str command. once in stream mode, characters received from a host mcu on the seria l interface are automatically transmit- ted to a remotely connected device via the ble wireless interface , and characters received from a remotely connected device on the ble wireless interface are seamlessly transmitted on the serial interface to the host m cu. configuration of the module is also possible using a re- motely connected application, however if the serial in- terface is configured to use command mode, remote applications are forbidden from accessing the com- mand interface. to grant a remote applicatio n access to the command interface, the serial interface must first place the module into stream mode to signal that it no longer requires access to the command parser. gpio configuration & usage the default gpio configuration of the module is shown in the following list , obtained by issuing the truconnect command sequence get gp u . the user uart, factory reset and i2c pins are configured by default. all other pins are unassigned or reserved. > get gp u ! # description # 0 i2c_sda # 1 i2c_scl # 2 us er_tx # 3 none # 4 none # 5 user_rx # 6 none,factory # 7 reserved # 8 none # 9 none # 10 none # 11 none # 12 none # 13 none # 14 none to configure a gpio pin for use, the pin must be as- signed a function. a large range of functions is ava ila- ble, please refer to the truconnect reference guide online ( at the following link ) for further information: http://truconnect.ack.me/commands#gfu
ams - 00x ? embedded bluetooth low energy solution regulatory certification, section 7 ads - ms00x - 107r ? preliminary data sheet page | 14 ?201 4 - 2015 ackme networks. http://ack.me september 14, 2015 7 regulatory certification the ams00x family of module s has been certified for operation in various regulatory domains. this section outlines certification information specific to the follow- ing countries and regions: ? united states ? canada ? europe ? australia ? new zea land should you require regulatory certification for the ams00x module in a country or region not listed, please contact your local ackme networks sales office or cre- ate a support request via our website at http://ack.me /cont act . 7.1 united states the ackme networks ams - 00x module has received federal communications commission (fcc) cfr47 tele- communications, part 15 sub - part c intentional radia- tors modular approval in accordance with part 15.212 modular transmitter approval. mo dular approval al- lows the end user to integrate the ams - 00x module into a finished product without obtaining subsequent and separate fcc approvals for intentional radiation, provided no changes or modifications are made to the module circuitry. changes or modifications could void the users authority to operate the equipment. the end user must comply with all of the instructions provided by the grantee which indicate installation and/or oper- ating conditions necessary for compliance. the finished product is required to comply with all ap- plicable fcc equipment authorization, regulations, re- quirements, and equipment functions not associated with the transmitter module portion. for example, compliance must be demonstrated to regulations for other transmitter com ponents within the host product; to requirements for unintentional radiators (part 15 sub - part b unintentional radiators), such as digital devices, computer peripherals, radio receivers, etc.; and to additional authorization requirements for non - transmit ter functions on the transmitter module (i.e. verification, or declaration of conformity) (e.g., trans- mitter modules may also contain digital logic functions) as appropriate. labeling and user information requirements the ams - 00x module has been labelled with a unique fcc id number, and if the fcc id is not visible when the module is installed inside another device, then the out- side of the finished product into which the module is installed must also display a label referring to the en- closed module. this e xterior label can use wording as follows: the user manual for the product should include the fol- lowing statement: c ontains fcc id: 2abpy - bb4ea - model no: AMS001 con tains fcc id: 2abpy - 0d06e - model no: ams002 this device complies with part 15 of the fcc rules. operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference rece ived, including interference that may cause un- desired operation. this equipment has been tested and found to com - ply with the limits for a class b digital device, pursu- ant to part 15 of the fcc rules. these limits are de- signed to provide reasonable protec tion against harmful interference in a residential installation. this equipment generates, uses and can radiate ra- dio frequency energy and if not installed and used in accordance with the instructions, may cause harm- ful interference to radio communications . however, there is no guarantee that interference will not oc- cur in a particular installation. if this equipment does cause harmful interference to radio or televi- sion reception, which can be determined by turning the equipment off and on, the user is enc ouraged to try to correct the interfe rence by one or more of the foll owing measures: ? reorient or relocate the receiving antenna. ? increase the separation between the equip- ment and receiver. ? connect the equipment into an outlet on a cir- cuit different from th at to which the receiver is connected. ? consult the dealer or an experienced radio/tv technician for help.
ams - 00x ? embedded bluetooth low energy solution regulatory certification, section 7 ads - ms00x - 107r ? preliminary data sheet page | 15 ?201 4 - 2015 ackme networks. http://ack.me september 14, 2015 additional information on labeling and user information requirements for part 15 devices can be found in kdb publication 784748 available at the fcc office of engi- neering and technology (oet) laboratory division knowledge database (kdb) at the following website: https://apps.fcc.gov/oetcf/kdb/index.cfm rf exposure all transmitters reg ulated by fcc must comply with rf exposure requirements. oet bulletin 65, evaluating compliance with fcc guidelines for human exposure to radio frequency electromagnetic fields, provides assis- tance in determining whether proposed or existing transmitting f acilities, operations or devices comply with limits for human exposure to radio frequency (rf) fields adopted by the federal communications com- mission (fcc). the bulletin offers guidelines and sugges- tions for evaluating compliance. if appropriate, complian ce with exposure guidelines for mobile and unlicensed devices can be accomplished by the use of warning labels and by providing users with information concerning minimum separation distances from transmitting structures and proper installation of antennas. the following statement must be included as a cau- tion statement in manuals and oem products to alert users of fcc rf exposure compliance: if the ams - 00x module is used in a portable application (i.e., the antenna is less than 20 cm from persons dur- ing o peration), the integrator is responsible for per- forming specific absorption rate (sar) testing in ac- cordance with fcc rules 2.1091. external antenna modular approval in the united states is permitted with the use of the integrated antenna only. if an exter nal antenna is used with the ams - 00x module, additional testing of the end product is needed to meet fcc re- quirements. further information additional information regarding fcc certification and use of the ams - 00x module in the united states is available fr om the following sources. ? federal communications commission (fcc) http://www.fcc.gov.au ? fcc office of engineering and technology (oet) laboratory division knowledge database (kdb) http://apps.fcc.gov/oetcf/kdb/index.cfm 7.2 canada the ams - 00x module has been certified for use in can- ada under industry canada (ic) radio standards specifi- cation (rss) rss - 210 and rssgen. modular approval permits the installation of a modul e in a host device without the need to recertify the device. labeling and user information requirements labeling requirements for the host device (from sec- tion 3.2.1, rss - gen, issue 3, december 2010): the host device shall be properly labeled to identify the module within the host device. the industry canada certification label of a module shall be clearly visible at all times when installed in the host device, otherwise the host device must be labeled to display the industry canada certification number of the module, preceded by the words contains transmit- ter module, or the word contains, or similar wording expressing the same meaning, as follows: user manual notice for license - exempt radio appa- ratus (from section 7.1.3 rss - gen, issue 3, december 201 0): user manuals for license - exempt radio appa- to satisfy fcc rf exposure requirements for mobile and base station transmission devices, a separation distance of 20 cm or more should be maintained between the antenna of this device and persons during operation. to ensure compliance, operation at closer than this distance is not recommended. the antenna(s) used for this transmitter must not b e co - located or operating in conjunction with any other an tenna or transmitter contains transmitter module ic: 11685a - 0d06e
ams - 00x ? embedded bluetooth low energy solution regulatory certification, section 7 ads - ms00x - 107r ? preliminary data sheet page | 16 ?201 4 - 2015 ackme networks. http://ack.me september 14, 2015 ratus shall contain the following or equivalent notice in a conspicuous location in the user manual or alterna- tively on the device or both: transmitter antenna notification (from section 7.1.2 rss - gen, issue 3, december 2010): user manuals for transmitters shall display the following notice in a con- spicuous location: the above notice may be affixed to the device instead of displayed in the user manual. user manuals for transmitters equipped with detach - able antennas shall also contain the following notice in a conspicuous location: immediately following the above notice, the manufac- turer shall provide a list of all antenna types approved for use with the transmitter, indicating the maximum permissible anten na gain (in dbi) and required imped- ance for each. external antenna types transmitter antenna (from section 7.1.2 rss - gen, issue 3, december 2010): the ams - 00x module can only be operated with the on - board antenna with which it was approved without ad- dition al testing. if an external antenna is used with the ams - 00x mod- ule, additional testing of the end product is needed to meet ic requirements as described in the previous sec- tion. further information additional information may be obtained from the in- dustry canada website at http://www.ic.gc.ca this device complies with industry canada license - exempt rss standard(s). operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this de vice must accept any interference, including interference that may cause undesired operation of the device. le prsent appareil est conforme aux cnr d'indus- trie canada applicables aux appareils radio exempts de licence. l'exploitation est autorise aux de ux onditions suivantes: (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appa- reil doit accepter tout brouillage radiolectrique subi, meme si le brouillage est susceptible d'en compromettre le fonctionnement. under industry can ada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by industry canada. to reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power ( eirp ) is not more t han that necessary for successful communication. conformment la rglementation d'industrie can - ada, le prsent metteur radio peut fonctionner avec une antenne d'un type et d'un gain maximal (ou infrieur) approuv pour l'metteur par indus- trie canada. dans le but de rduire les risques de brouil - lage radiolectrique l'intention des autres utilisa - teurs, il faut choisir le type d'antenne et son gain de sorte que la pui ssanc e isotrope rayonne quiva lente (p.i.r.e.) ne dpasse pas l'intensit ncessaire l'tablissement d'une communication satisfaisante. this radio transmitter (identify the device by certifi- cation number, or model number if category ii) has been approved by industry canada to operate with the antenna types listed below with the maximum permissible gain and required antenna impedance for each antenna type indicated. antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device. le prsent metteur radio (identifier le dispositif par son numro de certification ou son numro de modle s'il fait partie du matriel de catgorie i) a t approuv par industrie canada pour fonctionner avec les types d'antenne numrs ci - dessous et ayant un gain admissible maximal et l'impdance requise pour chaque type d'antenne. les types d'an- tenne non inclus dans cette liste, ou dont le gain est suprieur au gain maximal indiqu, son t strictement interdits pour l'exploitation de l'metteur.
ams - 00x ? embedded bluetooth low energy solution regulatory certification, section 7 ads - ms00x - 107r ? preliminary data sheet page | 17 ?201 4 - 2015 ackme networks. http://ack.me september 14, 2015 7.3 europe the ams - 00x module is an r&tte directive assessed radio module that is ce marked and has been manufac- tured and tested with the intention of being integrated into a final produ ct. the ams - 00x module has been tested to r&tte di- rective 1999/5/ec essential requirements for health and safety article 3.1(a), electromagnetic compatibility (emc) article 3.1(b), and radio article 3.2 and the re- sults are summarized in table 12 . a notified body opin- ion has also been issued. all ams - 00x test reports are available on the ackme networks website at http://ack.me /contact . the r&tte compliance association provides guidance on modular devic es in the document titled technical guidance note 01 available on the website at http://www.rtteca.com/html/download_area.htm . labeling and user information requirements the label on the fina l product which contains the ams - 00x module must follow ce marking requirements. the r&tte compliance association technical guidance note 01 provides guidance on final product ce marking external antenna requirements from r&tte compliance association docu ment tech- nical guidance note 01: provided the integrator installing an assessed radio module with an integral or specific antenna and in- stalled in conformance with the radio module manufac- turers installation instructions requires no further evaluation und er article 3.2 of the r&tte directive and does not require further involvement of an r&tte di- rective notified body for the final product. [ section 2.2.4 ] the european compliance testing listed in table 12 was performed using the a ms - 00x on - board antenna. further information a document that can be used as a starting point in un- derstanding the use of short range devices (srd) in europe is the european radio communications com- mittee (erc) recommendation 70 - 03 e, which can be downloade d from the european radio communications office (ero) at: http://www.ero.dk . further information may be obtained from the follow- ing websites: ? radio and telecommunications terminal equip- ment (r&tte) http://ec.europa.eu/enterprise/rtte/index_en.htm ? european conference of postal and telecommuni- cations administrations (cept) http://www.cept.org ? european telecommunications stand ards institute (etsi) http://www.etsi.org ? european radio communications office (ero) http://www.ero.dk ? the radio and telecommunications terminal equipment compliance association (r&tte c a) http://www.rtteca.com/ note : to maintain conformance to the testing listed in table 12 , the module shall be installed in accordance with the installation instructions in this data sheet and shall not be modified. when integrating a radio module into a completed product the integrator becomes the manufacturer of the final product and is therefore responsible for demonstrating compliance of the final product with the essent ial requirements of the r&tte directive.
ams00x ? embedded bluetooth low energy solution regulatory certification , section 7 ads - ms00x - 107r ? preliminary data sheet page | 18 ?201 4 - 2015 ackme networks. http://ack.me september 14, 2015 table 12 . european compliance testing AMS001 certification standard article laboratory report number date safety en 60950 - 1:2006 + a11:2009 + a1:2010 + a12:2011 3. 1(a) shenzhen morlab communications technology co., ltd. sz15010120a01 2015 - feb - 09 health en 50371:2002 - 03 sz15010120s01a 2015 - feb - 09 emc en 301 489 - 1 v1. 9.2 (20 11 - 0 9 ) 3.1(b) sz15010120e01a 2015 - feb - 09 en301 489 - 17 v2. 2 .1 (20 12 - 0 9 ) radio en 30 0 328 v1. 8 .1 (20 12 - 06 ) 3.2 sz15010120w04a 2015 - feb - 09 notified body opinion 0 700 - phoenix testlab 15 - 110950 2015 - feb - 13 ams002 certification standard article laboratory report number date safety en 60950 - 1:2006+a11:2009+a1:2010 3.1(a) shenzhen mo rlab communications technology co., ltd. sz14100103a01 2015 - jan - 07 health en 50371:2002 - 03 sz14100103s01a 2015 - jan - 04 emc en 301 489 - 1 v1. 9.2 (20 11 - 0 9 ) 3.1(b) sz14100103e01 2014 - nov - 11 en301 489 - 17 v2. 2 .1 (20 12 - 0 9 ) radio en 300 328 v1. 8 .1 (20 12 - 06 ) 3.2 sz14100103w04 2015 - jan - 06 notified body opinion 0 700 - phoenix testlab 15 - 110130 2015 - jan - 12 7.4 australia australian radio regulations do not provide a modular approval policy similar to the united states (fcc) and canada (ic). however, ams - 0 0x module test reports may be used in part to demonstrate compliance in ac- cordance with acma radio communications short range devices standard 2004 which references aus- tralia/new zealand industry standard as/nzs - 4268:2012. ams - 00x rf transmitter test rep orts may be used as part of the product certification and compliance folder. for further information regarding the availability of rf test reports, please contact ackme networks via our website at http://ack.me /contact . exter nal antenna requirements the compliance test reports provided in table 12 were performed using the ams - 00x on - board antenna. if an external antenna is used with the ams - 00x module, additional testing of the end product is needed t o meet australian regulatory requirements. further information additional information may be obtained from the aus- tralian communications and media authority website at http://www.acma.gov.au .
ams00x ? embedded bluetooth low energy solution regulatory certification , section 7 ads - ms00x - 107r ? preliminary data sheet page | 19 ?201 4 - 2015 ackme networks. http://ack.me september 14, 2015 7.5 new zealand new zealand radio regulations do not provide a modu- lar approval policy similar to the united states (fcc) and canada (ic). however, ams - 00x module test re- ports may be used in part to demonstrate compliance with the new zealand general user radio license for short ran ge devices. new zealand radio communica- tions (radio standards) notice 2010 references austral- ia/new zealand industry standard as/nzs - 4268:2012. ams - 00x rf transmitter test reports may be used as part of the product certification and compliance folder. for further information regarding the availability of rf test reports, please contact ackme networks via our website at http://ack.me /contact . external antenna requirements the compliance test reports provided in table 12 were performed using the ams - 00x on - board antenna. if an external antenna is used with the ams - 00x module, additional testing of the end product is needed to meet new zealand regulatory requirements. further information addition al information may be obtained from the new zealand radio spectrum ministry of economic devel- opment website at http://www.rsm.govt.nz .
ams00x ? embedded bluetooth low energy solution packaging, handling & storage, rohs, section 8 ads - ms00x - 107r ? preliminary data sheet page | 20 ?201 4 - 2015 ackme networks. http://ack.me september 14, 2015 8 packaging, handling & storage, rohs 8.1 packaging ams00x module s are shipped in a n esd bag. ams00x modules are also available in reels each cont aining 1000 modules . reels are shipped in an esd and moisture resistant sealed bag. the shelf life of the sealed bag is 12 months at 40c and <90% relative h umidity (rh). please refer to the bag seal date. 8.2 tape and reel specifications figure 7 - tape specifications symbol a0 b0 d0 e f k0 specification (mm) 11.8 0.10 18.1 0.10 1.5 0.10 1.75 0.10 14.2 0.10 2.70 0. 10 symbol p p0 p2 t w specification (mm) 20.0 0.10 4.00 0.10 2.00 0.10 0.30 0.05 32.0 0.30 ? tape material : black ps material, in line with rohs environmental management substances ? tape thickness: 0.3 mm 0.05 mm ? tape width: 32mm (1.3") ? prot ection zone: black ps material ? distance between chain hole centers within the range of 0.2 mm of cumulative error ? anti - camber at 1 mm / 250 mm ? all dimensions in line with the requirements of eia - 481 - d
ams00x ? embedded bluetooth low energy solution packaging, handling & storage, rohs, section 8 ads - ms00x - 107r ? preliminary data sheet page | 21 ?201 4 - 2015 ackme networks. http://ack.me september 14, 2015 figure 8 - reel specificat ions symbol a b c1 d e h t specification (mm) 2.5 0.2 11 0.2 330 1 99.5 0.1 13.2 0.2 32.8 + 0.3 / - 0.2 2.25 0.2
ams00x ? embedded bluetooth low energy solution packaging, handling & storage, rohs, section 8 ads - ms00x - 107r ? preliminary data sheet page | 22 ?201 4 - 2015 ackme networks. http://ack.me september 14, 2015 8.3 handling & storage caution msl3 sensitive device! ams00x module s are moisture sensi tive device s rated at moisture sensitive level 3 (msl3) per ipc/jedec j - std - 20 . after opening the moisture sealed storage bag, mod- ules that will be subjected to reflow solder or other high temperature processes must be: 1. mounted to a circuit board within 168 hours at factory conditions (30c and <60% rh) or 2. continuously stored per ipc/jedec j - std - 033 modules that have been exposed to moisture and envi- ronmental conditions exceeding packaging and storage conditions must be baked before mounting according to ipc/jedec j - std - 033 . failure to meet packaging and storage conditions will result in irreparable damage to modules during solder reflow. 8.4 rohs directive each ams00x module is produced according to the rohs (restr iction of the use of certain hazardous substances in electrical and electronic equipment) di- rective and complies with the directive.
ams00x ? embedded bluetooth low energy solution ordering information, section 9 ads - ms00x - 107r ? preliminary data sheet page | 23 ?201 4 - 2015 ackme networks. http://ack.me september 14, 2015 9 ordering information ams00x module s are available individually or in a reel of 10 00 units as described in the tables below . table 13 . AMS001 ordering information part number description AMS001/s 1 x AMS001 module with truconnect pre - installed. each module is individually packaged in an esd bag. AMS001/r a single reel containing 1000 x AMS001 modules, each with truconnect pre - installed. the entire reel is packaged in an esd and msl3 - rated moisture sensitive bag. table 14 . ams002 ordering information part number description ams002/s 1 x ams002 module with truconnect pre - installed. each module is individually packaged in an esd bag. ams002/r a single reel containing 1000 x ams002 modules, each with truconnect pre - installed. the entire reel is packaged in an esd and msl3 - rated moisture sensitive bag.
ams00x ? embedded blueto oth low energy solution revision history & glossary, section 10 ads - ms00x - 107r ? preliminary data sheet page | 24 ?201 4 - 2015 ackme networks. http://ack.me september 14, 2015 10 r evision history & glossary 10.1 revision history table 15 : document revision history revision date change desc ription ads - ms00x - 100 r 10 - nov - 2014 initial version ads - ms00x - 101r 7 - jan - 2015 note minimum boot voltage add packaging section ads - ms00x - 102r 2 - feb - 2015 note pull - up requirement and minimum deep sleep current ads - ms00x - 103r 2 - feb - 2015 finalized ams002 c e regulatory information for ams002 ads - ms00x - 104r 8 - apr - 2015 added limits for io pins finalized AMS001 regulatory information ads - mw00x - 105r 9 - jun - 2015 updated gpio and pin definitions in pin and signal descriptions ads - mw00x - 106r 28 - aug - 2015 added max imum voltage details for input and output pins added vias diagram to routing recommendations added tape and reel documentation. removed tray packaging details. ads - mw00x - 10 7 r 1 4 - sep - 2015 added adaptive frequency hopping to features and description. 10.2 glossary in most cases, acronyms and abbreviations are defined on first use. a comp rehensive list of acronyms and other terms used in ackme networks documents are provided on the ackme networks website at http://ack.me/faqs/glossary .
ams00x ? embedded bluetooth low energy solution ack me reserves the right to make changes without further notice to any products or data herein to improve reliability, function, or design. information furnished by ack me is believed to be accurate and reliable. however, ack me does not assume any liability arising out of the application or use of this information, nor the application or use of any product described herein, neither does it convey an y license under its patent rights nor the rights of others . ack me networks 20 north santa cruz ave los gatos ca 95030 united states ? 2014 - 2015 ack me networks inc. all rights reserved. ads - ms00x - 107r ? preliminary data sheet september 14, 2015 contact information +1 (408) 402 8160 http://ack.me/contact phone:

▲Up To Search▲

Price & Availability of AMS001

	To Download AMS001 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .